Bisnis

Tio1608-D2I/O Rack

Dapat digulir

Spesifikasi Umum Sampling frequency rate Eksternal 44.1kHz, 48kHz, 88.2kHz, 96kHz
Signal delay Kurang dari 1,3 ms INPUT ke OUTPUT, terhubung dengan DM3, Dante Receive Latency diatur ke 0,25 ms (satu arah), Fs = 96kHz; Kurang dari 2,6 ms INPUT ke OUTPUT, terhubung dengan DM3, Dante Receive Latency diatur ke 0,25 ms (satu arah), Fs = 48kHz
Total harmonic distortion Kurang dari 0,2% +4 dBu@20Hz-20kHz ke 600Ω, Gain=+66 dB / Kurang dari 0,05% +4 dBU@20Hz-20kHz ke 600Ω, Gain=-6 dB, INPUT ke OUTPUT, Fs=88,2kHz, 96kHz; Kurang dari 0,1% +4 dBu@20Hz-20kHz ke 600Ω, Gain=+66 dB / Kurang dari 0,05% +4 dBU@20Hz-20kHz ke 600Ω, Gain=-6 dB, INPUT ke OUTPUT, Fs=44,1kHz, 48kHz *Diukur dengan filter -18 dB/oktaf @ 80kHz
Frequency response +0,5, -1,5 dB 20Hz-20kHz, lihat level output nominal @1kHz, INPUT ke OUTPUT
Dynamic Range 108 dB, INPUT ke OUTPUT, Gain=-6 dB / 110 dB, Konverter DA, Fs 96kHz; 108 dB, INPUT ke OUTPUT, Gain=-6 dB / 112 dB, Konverter DA, Fs 48kHz
Hum & noise level Equivalent input noise -128 dBu, Gain=+66 dB, Fs 96kHz, 48kHz *Diukur dengan filter A-weight
Residual output noise -86 dBu, Fs 96kHz / -88 dBu, Fs 48kHz, ST main off *Diukur dengan filter A-weight
Crosstalk -100 dB, channel INPUT/OUTPUT yang berdekatan, Gain Input = -6 dB *Diukur dengan filter -30 dB/oktaf @22kHz
Disipasi panas 100-240V, 50/60Hz, 43,5 kkal/jam
Persyaratan daya 100-240V, 50/60Hz
Konsumsi daya 50W
Dimensi P 480mm (18,9”)
T 88mm (3,5”)
L 364mm (14,4”)
Berat Bersih 5,7 kg (12,6 lb)
Aksesori Panduan Pemilik, Kabel Daya (2,5 m), Penahan karet (4)
Lain-lain Kisaran Suhu: Kisaran suhu pengoperasian: 0 - 40℃, Kisaran suhu penyimpanan: -20 - 60℃
Temukan Produk Serupa

Analog Input Characteristics

Input Terminals GAIN Actual Load Impedance For Use With Nominal Input Level Connector Balanced / Unbalanced
Sensitivity *1 Nominal Max. before clip
INPUT 1-16 +66 dB 7.5kΩ 50-600Ω Mics & 600Ω Lines -82 dBu (61.6μV) -62 dBu (0.616mV) -42 dBu (6.16mV) Combo Jack (XLR-3-31 type *2 or TRS phone *3) Balanced
-6 dB +10 dBu (245mV) +10 dBu (2.45V) +30 dBu (24.5V)

In these specifications, 0 dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
*1. Sensitivity is the lowest level that will produce an output of +4 dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND

Analog Output Characteristics

Output Terminals Actual Source Impedance For Use With Nominal Output Level Connector Balanced / Unbalanced
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +4 dBu (1.23V) +24 dBu (12.3V) XLR-3-32 type *1 Balanced

In these specifications, 0 dBu = 0.775Vrms.
*1. 1: GND, 2: HOT, 3: COLD

Digital Input & Output Characteristics

Terminal Format Data length Level Audio Connector
Primary / Secondary Dante 24bit or 32bit 1000Base-T 16ch (Tio1608-D2 to other devises)
8ch (Other devises to Tio1608-D2)		 etherCON Cat5e
to page top

Select Your Location